Intermec CN30 Manual de usuario Pagina 118
- Pagina / 196
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3 — Configuring the CN30
106 CN30 Mobile Computer User’s Manual
AutoCab only installs the CAB file if it was not installed before by Auto-
Cab. To track the installation of a CAB file, AutoCab marks the CAB file
with the System attribute. This attribute is ignored if the device is perform-
ing a cold-boot on a non-persistent file system.
AutoCab preserves the CAB file after installation if the ReadOnly attribute
is set. If not set, the CAB file is deleted automatically after installation.
Usage:
AutoCab [-ChkRst=][-File=][-Force][-Log=][-Move=][-Quiet=][-Show=][-Signal=]
Command line switches are described below.
If <PathName> references a single CAB file, that file is processed. If <Path-
Name> references a directory, all the .CAB files in that directory is pro-
cessed. If <PathName> is a wild card pattern, all files matching that pattern
is processed, If <PathName> is omitted, InstallCab processes all the .CAB
files in directory “\CabFiles.”
Example:
; Install all cab files in the \Flash File Store\XYZ directory, regardless.
AutoCab -FILE="\Flash File Store\XYZ\*.cab" -FORCE
; Install only one cab file, use Intermec cab installation display
AutoCab -FILE=”\myCab\app.cab” =show=2
Customizing How Applications Load on the CN30 Computer
If you have several processes that you need running in a specific order as the
CN30 Computer turns on, you can use the AutoRun system to customize
the way applications load. For compatibility with other Intermec comput-
ers, you can place a copy of AUTORUN.EXE in the same folder as your
AUTORUN.DAT file but it is not required.
-ChkRst= Set to 1 to configure AutoCab to check for the Reset flag after all CAB files are installed. This file is cre-
ated by CAB files that want a warm reset after installation. Default is 0 (do not check for flag).
-File= Specifies the CAB files to extract. Note that the specified files need not end with the .CAB extension.
-Force Forces the specified CAB files to extract regardless of whether it was previously extracted.
-Log= Set to 1 to create a log file in the same folder that AutoCab is running. Useful for debugging CAB
installation. Default is 0 (disabled).
-Move= Set to 1 to force source CAB file deletion, even when read-only bit set on file. Default is 0 (disabled).
-Quiet= Set to 0 to allow AutoCab to display user message box on errors. Useful for debugging CAB installation.
Default is 1 (keep quiet).
-Show= Set to 0 to prevent showing any installation progress interfaces. Also prevents user from canceling instal-
lation. Set to 1 to show normal installation. Set to 2 to show Intermec installation progress interface
(user can see what is installing but cannot cancel it). Default is 1 (show normal).
-Signal= Set to string name of signal to use at the completion of CAB installation before a reboot occurs (if
enabled). AutoCab uses WaitForSingleObject on this name. Default is disabled.
- Computer 1
- User's Manual 1
- Contents 3
- Global Services and Support 10
- Who Should Read This Manual 11
- Related Documents 11
- Patent Information 11
- Before You Begin 12
- Using the CN30 Mobile 13
- Intermec 14
- Ready-to-work 14
- Indicator 14
- Scan Buttons 14
- Battery Light 14
- Headset Jack 15
- Main Speaker 15
- Front Speaker 15
- Using the Battery 16
- Maximizing Battery Life 17
- Checking the Battery Status 17
- Flashes red on low 18
- Adjusting the Beeper 19
- Select a Beeper Volume 20
- Disabling the Beeper 20
- Using the Keypad 21
- The 56-Key Keypad 22
- Orange key 23
- Green key 23
- Scan buttons 23
- Backlight key 23
- Magnifier Application 25
- Using the Power (I) Key 26
- Using the Screen 27
- Reset Button 28
- CN30 Console 28
- Software Build Version 29
- Using the Speakers 30
- Using the Status Lights 31
- Scanning Bar Codes 32
- StorageMedia 34
- Using the SD Card 35
- Hardware 36
- Operating System 36
- Software 36
- Bar Code Scanning 36
- Standard Communications 36
- Wireless LAN 37
- Device Management 37
- Electrical Specifications 38
- Screen Specifications 38
- Regulatory Approvals 38
- CN30 Quad Charger 39
- CN30 Charge Dock 39
- CN30 Belt Clip 39
- CN30 Handstrap 39
- CN30 Scan Handle 39
- Windows Mobile 41
- Software Builds 42
- Where to Find Information 42
- Basic Skills 43
- Programs 44
- Pop-up Menus 45
- Notifications 45
- Entering Information 46
- Using Block Recognizer 48
- Using Letter Recognizer 49
- Using Transcriber 49
- Selecting Typed Text 49
- Writing on the Screen 50
- Before Recognition 51
- After Recognition 51
- Drawing on the Screen 52
- Recording a Message 52
- Tap to begin recording 53
- Using My Text 54
- Adjusting Settings 55
- Adding or Removing Programs 55
- Note this information 56
- Removing Programs 58
- Microsoft ActiveSync 59
- Microsoft Pocket Outlook 60
- Synchronizing Calendar 61
- What’s an All Day Event? 62
- What’s a Recurrence Pattern? 63
- Viewing Appointments 63
- Creating an All-Day Event 65
- Sending a Meeting Request 68
- Finding an Appointment 69
- Deleting an Appointment 70
- Changing Calendar Options 70
- Creating a Contact 71
- Synchronizing Contacts 72
- Viewing Contacts 72
- Adding a Note to a Contact 73
- Copying a Contact 74
- Finding a Contact 74
- Deleting a Contact 75
- Changing Contacts Options 75
- Tasks: Keeping a To Do List 76
- Synchronizing Tasks 77
- Creating a Note 78
- Synchronizing Notes 78
- Synchronizing E-mail Messages 80
- Connecting to a Mail Server 81
- Companion Programs 83
- Creating a Document 85
- Typing Mode 86
- Writing Mode 86
- Excel Mobile 87
- Creating a Workbook 89
- PowerPoint Mobile 90
- Internet Explorer Mobile 93
- Mobile Favorites 94
- Getting Connected 96
- Connecting to Work 99
- Ending a Connection 103
- Setting Up an E-mail Account 104
- Configuring the CN30 107
- PreShell 112
- PostShell 112
- RunAutoRun 113
- AutoExec 114
- AutoCopy 116
- Configuring CN30 Parameters 119
- Documentation 125
- About the Application 125
- COM Ports 128
- Wireless Printing 130
- Bluetooth Audio 134
- Selecting Audio Mode 134
- Reprogramming the CN30 Keypad 135
- Registry Entries 136
- Programming the Keypad 136
- Alphanumeric Scan Codes 137
- Numeric Scan Codes 137
- Configuring the SF51 Scanner 138
- Configuring Security 141
- Wireless Network 142
- Terminology 142
- Configuring Funk Security 143
- Using WPA Security 143
- Using 802.1x Security 146
- Using LEAP Security 147
- Using Static WEP Security 148
- Using the Profile Wizard 149
- Advanced 165
- Maintaining the CN30 173
- Network Support 181
- Via Intermec Settings 182
- Ethernet Communications 182
- Chapter 5 — Network Support 183
- AutoIP/DHCP 184
- *961-054-039A* 196
Relacionado con productos y manuales para Computadoras móviles de mano Intermec CN30
(452 paginas)
(2 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.219 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales