Intermec CN30 Manual de usuario Pagina 122
- Pagina / 196
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3 — Configuring the CN30
110 CN30 Mobile Computer User’s Manual
Example
In the host application, you want to get the current values of two configura-
tion commands from the CN30 Computer. Send the CG$+NABV transaction
from the host application
where:
The CN30 returns the
CgS+BV4 transaction to the host application, where:
Configuring the CN30 Computer in a UDP Plus Network
You can use the host computer to configure a CN30 Computer in your
wireless or Ethernet network. To send and receive configuration data or
files, you need to write a host application that can communicate with an
Intermec Application Server (formerly Gateway or DCS 30X).
For help, see the appropriate Gateway or DCS 30X User’s Manual. Use the
Terminal Message Format (TMF) protocol to send and receive transactions
between the host application and the CN30 Computer.
To set up the Intermec Application Server, configure a peer-to-peer destina-
tion name for the host application. Create a transaction ID, $NGCFGRSP,
that routes to this destination name. The Intermec Application Server uses
the transaction ID to route responses from the CN30 Computer back to
the host application. $NGCFGRSP is a special transaction ID that the
server uses to forward configuration response data from a CN30.
All configuration responses are routed with the $NGCFGRSP transaction
ID. The Intermec Application Server cannot track multiple applications
sending reader or configuration commands. If you have two host applica-
tions sending reader or configuration commands, they must both be con-
figured to receive the $NGCFGRSP transactions, and therefore both
receive all responses from all CN30 Computers.
To set up the host computer, verify that the host computer can communi-
cate with the Intermec Application Server.
Note: The transaction header is not shown in this example. You do not
need a transaction header for a host application in a TCP/IP network, but
you do for a UDP Plus network.
CG is a TMF Configuration Get request.
$+ is the Change Configuration reader command.
BV is the Beeper Volume configuration command.
Cg is a TMF Configuration Get response.
$+ is the Change Configuration reader command.
BV4 means the Beeper Volume configuration command is currently set to a
value of 4, which is a very high beeper volume.
- Computer 1
- User's Manual 1
- Contents 3
- Global Services and Support 10
- Who Should Read This Manual 11
- Related Documents 11
- Patent Information 11
- Before You Begin 12
- Using the CN30 Mobile 13
- Intermec 14
- Ready-to-work 14
- Indicator 14
- Scan Buttons 14
- Battery Light 14
- Headset Jack 15
- Main Speaker 15
- Front Speaker 15
- Using the Battery 16
- Maximizing Battery Life 17
- Checking the Battery Status 17
- Flashes red on low 18
- Adjusting the Beeper 19
- Select a Beeper Volume 20
- Disabling the Beeper 20
- Using the Keypad 21
- The 56-Key Keypad 22
- Orange key 23
- Green key 23
- Scan buttons 23
- Backlight key 23
- Magnifier Application 25
- Using the Power (I) Key 26
- Using the Screen 27
- Reset Button 28
- CN30 Console 28
- Software Build Version 29
- Using the Speakers 30
- Using the Status Lights 31
- Scanning Bar Codes 32
- StorageMedia 34
- Using the SD Card 35
- Hardware 36
- Operating System 36
- Software 36
- Bar Code Scanning 36
- Standard Communications 36
- Wireless LAN 37
- Device Management 37
- Electrical Specifications 38
- Screen Specifications 38
- Regulatory Approvals 38
- CN30 Quad Charger 39
- CN30 Charge Dock 39
- CN30 Belt Clip 39
- CN30 Handstrap 39
- CN30 Scan Handle 39
- Windows Mobile 41
- Software Builds 42
- Where to Find Information 42
- Basic Skills 43
- Programs 44
- Pop-up Menus 45
- Notifications 45
- Entering Information 46
- Using Block Recognizer 48
- Using Letter Recognizer 49
- Using Transcriber 49
- Selecting Typed Text 49
- Writing on the Screen 50
- Before Recognition 51
- After Recognition 51
- Drawing on the Screen 52
- Recording a Message 52
- Tap to begin recording 53
- Using My Text 54
- Adjusting Settings 55
- Adding or Removing Programs 55
- Note this information 56
- Removing Programs 58
- Microsoft ActiveSync 59
- Microsoft Pocket Outlook 60
- Synchronizing Calendar 61
- What’s an All Day Event? 62
- What’s a Recurrence Pattern? 63
- Viewing Appointments 63
- Creating an All-Day Event 65
- Sending a Meeting Request 68
- Finding an Appointment 69
- Deleting an Appointment 70
- Changing Calendar Options 70
- Creating a Contact 71
- Synchronizing Contacts 72
- Viewing Contacts 72
- Adding a Note to a Contact 73
- Copying a Contact 74
- Finding a Contact 74
- Deleting a Contact 75
- Changing Contacts Options 75
- Tasks: Keeping a To Do List 76
- Synchronizing Tasks 77
- Creating a Note 78
- Synchronizing Notes 78
- Synchronizing E-mail Messages 80
- Connecting to a Mail Server 81
- Companion Programs 83
- Creating a Document 85
- Typing Mode 86
- Writing Mode 86
- Excel Mobile 87
- Creating a Workbook 89
- PowerPoint Mobile 90
- Internet Explorer Mobile 93
- Mobile Favorites 94
- Getting Connected 96
- Connecting to Work 99
- Ending a Connection 103
- Setting Up an E-mail Account 104
- Configuring the CN30 107
- PreShell 112
- PostShell 112
- RunAutoRun 113
- AutoExec 114
- AutoCopy 116
- Configuring CN30 Parameters 119
- Documentation 125
- About the Application 125
- COM Ports 128
- Wireless Printing 130
- Bluetooth Audio 134
- Selecting Audio Mode 134
- Reprogramming the CN30 Keypad 135
- Registry Entries 136
- Programming the Keypad 136
- Alphanumeric Scan Codes 137
- Numeric Scan Codes 137
- Configuring the SF51 Scanner 138
- Configuring Security 141
- Wireless Network 142
- Terminology 142
- Configuring Funk Security 143
- Using WPA Security 143
- Using 802.1x Security 146
- Using LEAP Security 147
- Using Static WEP Security 148
- Using the Profile Wizard 149
- Advanced 165
- Maintaining the CN30 173
- Network Support 181
- Via Intermec Settings 182
- Ethernet Communications 182
- Chapter 5 — Network Support 183
- AutoIP/DHCP 184
- *961-054-039A* 196
Relacionado con productos y manuales para Computadoras móviles de mano Intermec CN30
(452 paginas)
(2 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales